Pontiac was actually launched as “the Chief of the Sixes” in 1926. It was a lighter “companion car” for the Oakland. The Pontiac sold well, while the popularity of the Oakland declined. By 1932, the company dropped Oakland (which had a V8) and offered a Pontiac flathead V8. It used the basic engine as the Oakland, although it had some detail changes. A year later, the straight eight replaced the early V8. This type of engine then survived at Pontiac until 1954.
A lot of people think that all Pontiac straight eights are the same. The original 1933 version was 223.4 cubic inches and produced 77 hp. Displacement was unchanged in 1934, but horsepower jumped up to 84. Those specs were retained for 1935. In 1936, the numbers were 232.3 cid and 87 hp. The 248.9-cid 100-hp version of 1937 was carried over through 1939. In 1940, the size stayed the same, but three extra ponies were advertised. Things remained like this right through 1947. When Hydra-Matic Drive was introduced in 1948, the stick-shift engine stayed at 103 hp, but the “high head” (short for high-compression and meaning 7.5:1 instead of 6.5:1 compression) engine used with the automatic transmission had a 106-hp rating. This was carried over for the 1949 model year.
Starting in 1950, the straight eight was bored out a quarter inch to 268.4 cubes where it stayed from then on. That year, horsepower was 108 with standard shift and 113 with Hydra-Matic and in 1951 the respective ratings were 116 and 120.
Right from the beginning, the Pontiac straight eight had five main bearings and solid valve lifters in the side of the block. A Carter one-barrel carburetor was used through 1939. A Carter two-barrel was used from then on. In 1947 the dual-throat carb was switched from a Carter WDO to a Carter WCD. The WCD was also used on Buick 8s and was then modified for early 1960s Ramblers, putting the linkage on the opposite side. Rebuild kits are the same, though. If your parts supplier can’t find a Pontiac carb kit listed, try looking for Buick or Rambler parts.Two ponies were added to each in 1952-’53. In the last straight eight year, 1954, the synchromesh engine’s rating was 122 hp and the high-head version advertised 127 hp. That was the maximum output before the V8 arrived.
Various other accessories on the Pontiac eights changed from time to time. For instance, the metal spark plug wire looms have the same look in 1952-1953, but were changed in 1954.
Both the carburetors and generators on these Pontiacs have provisions for oiling. If you tell the young man at the Quik Lube to oil your generator, he’ll first have no idea what a generator is, and when you explain that it’s like an alternator, he’ll tell you that it doesn’t need oil. It does!
The Pontiac Eight was offered with Hydra-Matic Drive for the first time in 1948. Cars with this option used a unique linkage that operated off the foot-operated starter motor. The linkage chokes the carburetor, squirts a drop of fuel into it and moves the gear shifter from the reverse position (used for parking) into neutral, while starting the engine. Most of the time, if you bypass the linkage and try to start the car in the conventional way, you will flood the engine.
Apparently, the question of value was raised because many hot rodders who buy a pre-1955 Pontiac immediately yank out the stately L-head engine and Army-tank-proved Hydra-Matic in favor of a hotter mill. They install modern V8s. In most cases, a Chevy 350-cid V-8 replaces the factory-installed straight eight with a Turbo Hydra-Matic transmission behind it. This leaves the hot rodders with a big hunk of iron they then want to sell. It then becomes “rare and valuable.”Pontiac straight eights seem to be catching on a little bit with hot rodders wanting to put something different under the hood of a car they’re building. There’s a lot of good information about these engines posted on the HAMB—a popular hot rod Internet bulletin board. People are also asking how much these engines are worth. The consensus among hot rodders seems to be that the Pontiac eight is a “boat anchor” that isn’t worth a lot, but a few feel differently.
These fellows aren’t too interested in the Pontiac Eight’s reputation for being a 100,000-mile engine when many other motors tended to last 60 percent as long. A few rodders do get a little creative and ask about the availability of vintage speed equipment for the Pontiac Eight.
They want to know if aftermarket suppliers back in the day offered fined aluminum heads or split manifolds for this motor.
Some such hardware was produced in the early ‘50s, although the 1949 Bell Auto Parts Catalog only listed speed equipment for Ford flathead sixes, Studebaker Champion sixes and Chrysler and De Soto flatheads, in addition to the normal Ford and Mercury V-8
An interesting article touching on straight eight performance was a road test of several cars in which a ‘54 Pontiac Eight pulling a trailer was compared to contemporary V8s similarly equipped.goodies. A few modern hot rodders fabricate their own Pontiac Eight performance parts and some look pretty cool. At least one Pontiac “flattie” was headed to Bonneville last year.
The cars were tested pulling a trailer and not pulling a trailer. The test results indicated that the Pontiac Eight performed the best of the pack when the trailer was attached since it “out-torqued” them.
So what is a Pontiac straight eight engine worth to a collector? There have been ads in collector publications asking as much as $2,000 for a straight eight and someone on the HAMB said he’d sell his for $100.
In the real world, people in the know about these engines will pay $400-$500 for a good used one. A Pontiac collector restoring a car with a bad engine will probably spend more.
An unused new-old-stock straight eight long block or an entire engine that has been correctly rebuilt would be a steal at $2,000. A complete rebuild of such an engine with no cutting of corners can cost as much as $1,000 per hole or $8,000 according to professional rebuilders.
If a car collector brings a Pontiac straight eight to your shop to have it rebuilt, where do you get parts for it? California Pontiac Restoration (www.pontiacparts.net) advertises Master Overhaul Kits in the Pontiac-Oakland Club International (www.poci.org) magazine Smoke Signals.Of course, if you remove that heavy engine and take it to a machine shop, then pick it up, put it together and re-install it yourself, you might beat this price if you don’t count your labor. So, it is easy to understand why a lot of pre-1954 Pontiacs are getting V8s today.
The CPR kits include pistons, piston rings, main bearings, rod bearings, cam bearings, an overhaul gasket set, a timing chain and gear set, valve springs, an oil pump kit, free valve locks, freeze plugs, a zinc additive and cam grease. The kit for 1937-1949 engines is $1,596 and the kit for 1950-1954 engines is $1,271.
If you have a Pontiac eight earlier than 1937 vintage or if you want to compare suppliers for other reasons such as parts brands and price, vintage engine parts suppliers such as Egge Machine (www.egge.com), California Obsolete Engine Parts (www.danamotorssac.com), Northwestern Auto Supply (www.northwesternautosupply.com), Kanter Auto Products (www.kanter.com) and Terrill Machine (www.deleontexas.com/chamber/tmachine.php ) would be good places to look for help with engine parts.
Finally, if you need specifications, copies of shop manual pages and other materials that provide instructions on rebuilding a Pontiac straight eight engine, the Pontiac-Oakland Automobile Museum (www.pontiacoaklandmuseum.org) in Pontiac, Ill., houses a large archive of such materials and a research service is available.(For additional suppliers not listed here, refer to the Engine Builder Buyer’s Guides)
For more information on this contact Tim Dye at the Pontiac-Oakland Museum and Resource Center, 205 N. Mill St., Pontiac, IL 61764. Call (815) 842-2345 or email [email protected]